Tag: Jet washing

  • Jet washing driveways: is it safe for block paving and tarmac?

    Jet washing driveways: is it safe for block paving and tarmac?

    Jet washing is generally safe for block paving and tarmac if it is done with care: a moderate setting, a flat fan nozzle, the lance kept moving at a low angle, and the joints refilled afterwards on block paving. Problems usually come from holding the jet too close, using too much pressure or treating every surface the same. This guide to jet washing driveways in Nantwich explains what each surface can take and how to get a clean finish without damage.

    Why driveways need cleaning before winter

    By November, most Cheshire driveways have collected a season’s worth of leaves, tyre marks, moss and green algae. In a mild, damp winter that film rarely dries out, and shaded drives under trees and hedges can become slippery underfoot.

    A careful clean now makes the drive safer to walk on during dark mornings and evenings, and stops moss and weeds settling into the joints and edges over the colder months.

    Jet washing block paving: what to watch for

    Block paving is made up of individual blocks laid on a bed of sand, with fine sand brushed into the joints. That jointing sand locks the blocks together. It is also the part most easily damaged by jet washing.

    The main risks

    • Washed-out joints. A strong jet aimed into the gaps blows the sand out, which lets blocks shift and gives weeds an easy home.
    • Surface etching. Holding the nozzle too close can roughen the face of concrete blocks and expose the aggregate underneath.
    • Striping. Uneven passes leave light and dark bands that stay visible for months.

    How to do it well

    1. Sweep the drive and scrape moss and weeds out of the joints first.
    2. Use a flat fan nozzle or a rotary surface cleaner attachment, which spreads the force evenly.
    3. Keep the lance at a low angle and work diagonally across the blocks, so the jet does not run straight down the joints.
    4. Overlap each pass slightly for an even finish.
    5. Once fully dry, brush kiln-dried sand or a suitable jointing compound back into the joints.

    Refilling the joints is not optional. Skipping it is the most common reason block paving looks worse a few months after being cleaned.

    Is jet washing safe for tarmac?

    Tarmac is more flexible and softer than concrete. It can be cleaned with a pressure washer, but it needs a gentler approach.

    • Use a lower setting. Too much pressure can loosen the small stones in the surface, especially on older or worn tarmac.
    • Keep your distance. Hold the nozzle further back than you would on concrete and keep it moving.
    • Avoid turbo or rotating point nozzles. They concentrate the jet into a small area and can gouge the surface.
    • Treat oil stains separately. A degreaser made for driveways usually works better than more pressure.

    If the tarmac is already crumbling or breaking up at the edges, jet washing can make it worse. In that case, a gentle brush and rinse is the safer option, and it may be worth asking a driveway specialist about repairs.

    Other driveway surfaces

    Concrete

    Plain concrete is usually the most forgiving surface and responds well to pressure washing, though the same rules on distance and angle still apply.

    Imprinted or pattern concrete

    These drives are often sealed. Too much pressure can strip or cloud the sealant, so start gently and test a small area first.

    Resin-bound and resin-bonded

    Resin surfaces can be damaged by high pressure and some chemicals. Follow the installer’s care advice where you have it, and use a low setting with plenty of distance.

    Gravel

    Gravel drives are not suitable for jet washing. Raking, weeding and topping up the gravel is the better approach.

    For patios, which are often natural stone and need a slightly different approach, our post on patio cleaning before winter covers what to do.

    Looking after the drive once it is clean

    • Think about the run-off. Rinse water often flows into surface drains, so keep chemical use to a minimum and choose products intended for outdoor use.
    • Avoid freezing weather. Do not jet wash when frost is forecast, as water held in the surface and joints can freeze.
    • Sweep regularly. Clearing leaves every week or two through autumn stops the green film returning so quickly.
    • Keep gutters clear. An overflowing gutter or downpipe can soak one part of the drive all winter. Our guide on how often to clean gutters in Cheshire explains what to check.

    When to bring in help

    Cleaning a full driveway properly is a long, wet job, and the refilling afterwards adds more time. It also takes some judgement to know how much pressure each surface can take.

    Jet washing is one of the outside jobs we take on for homes in Nantwich and nearby villages such as Willaston, Stapeley and Shavington. It sits alongside our garden maintenance work, so the drive, patio, paths and garden can all be looked after together.

    Frequently asked questions

    Will jet washing damage my block paving?

    Not if it is done carefully. Use a fan nozzle or surface cleaner, keep a low angle and refill the joints with sand once the paving is dry.

    Can you pressure wash a tarmac drive?

    Yes, on a lower setting with the nozzle held further back and kept moving. Avoid turbo nozzles, and do not jet wash tarmac that is already breaking up.

    How often should a driveway be jet washed?

    For most drives, once or twice a year is plenty, with regular sweeping in between. Shaded drives under trees may need attention more often.

    Is it OK to jet wash a driveway in winter?

    Only on a mild, dry day with no frost forecast. Water left in the surface and joints can freeze and cause damage or ice.

    If you would like your drive cleaned carefully before winter, you can request a free quote.